0
TECHNICAL PAPERS

Consistent and Minimal Springback Using a Stepped Binder Force Trajectory and Neural Network Control

[+] Author and Article Information
Jian Cao, Brad Kinsey

Department of Mechanical Engineering, Northwestern University, Evanston, IL 60208

Sara A. Solla

Department of Physics and Astronomy, Northwestern University, Evanston, IL 60208; Department of Physiology, Northwestern University Medical School, Chicago, IL 60611

J. Eng. Mater. Technol 122(1), 113-118 (Jun 14, 1999) (6 pages) doi:10.1115/1.482774 History: Received June 20, 1998; Revised June 14, 1999
Copyright © 2000 by ASME
Your Session has timed out. Please sign back in to continue.

References

Ayres,  R. A., 1984, “SHAPESET: A Process to Reduce Sidewall Curl Springback in High-Strength Steel Rails,” J. Appl. Metalwork., 3, No. 2, pp. 127–134.
Hishida,  Y., and Wagoner,  R., 1993, “Experimental Analysis of Blank Holding Force Control in Sheet Forming,” J. Mater. Manufact., 2, pp. 409–15.
Sunseri,  M., Cao,  J., Karafiltis,  A. P., and Boyce,  M. C. 1996, “Accommodation of Springback Error in Channel Forming Using Active Binder Force Control: Numerical Simulations and Results,” ASME J. Eng. Mater. Technol., 118, No. 3, pp. 426–35.
Cho,  S., Cho,  Y., and Yoon,  S., 1997, “Reliable Roll Force Prediction in Cold Mill Using Multiple Neural Networks,” IEEE Trans. Neural Netw., 8, No. 4, pp. 874–82.
Di,  S., and Thomson,  P. F., 1997, “Neural Network Approach for Prediction of Wrinkling Limit in Square Metal Sheet Under Diagonal Tension,” J. Test. Eval., 25, pp. 74–81.
Elkins, K. L., 1994, “On-Line Angle Control for Small Radius Air Bending,” Carnegie Mellon University, UMI Dissertation Services, Ph.D. thesis.
Yang, M., Shima, S., and Watanabe, T., 1992, “Development of Control System Using Neural Network Combined with Deformation Model for an Intelligent V-Bending Process of Sheet Metals.” Proceedings of Japan/USA Symposium on Flexible Automation, ASME, Vol. 2, pp. 1485–90.
Forecellese, A., Gabrielli, F., and Ruffini, R., 1997, “Springback Control in a Air Bending Process by Neural Network,” Submitted to Proc. III Convergno AITEM.
Ruffini, R., and Cao, J., 1998, “Using Neural Network for Springback Minimization in a Channel Forming Process,” Developments in Sheet Metal Stamping, SAE Paper 98M-154, SP-1322. pp. 77–85.
Graf, A. and Hosford, W., 1993, “Plane-strain Tension Test of AL 2008-T4 Sheets,” Proceedings SAE Congress Symposium on Sheet Forming, Detroit, MI.
ABAQUS, 1997, User’s Manual, Theory Manual, Version 5.6, Hibbit, Karlsson, and Sorensen, Providence, RI.
Kinsey, B., and Cao., J., 1997, “An Experimental Study to Determine the Feasibility of Implementing Process Control to Reduce Part Variation in a Stamping Plant,” Sheet Metal Stamping: Development Applications. SAE Paper 970713, SP-1221, pp.107–12.
Rumelhart, D. E. and McClelland, J. L., 1986, “Learning Internal Representation by Error Propagation,” Parallel Distributed Processing, MIT Press, Cambridge, MA. Vol. 1, Ch. 8.
Widrow,  B., and Lher,  M. A., 1990, “30 Years of Adaptive Neural Networks: Perception, Madaline and Backpropagation,” Proc. IEEE, 78, No. 9, pp. 1415–41
Kinsey, B., 1998, “Process Control in Sheet Metal Forming,” Master’s thesis, Department of Mechanical Engineering, Northwestern University.

Figures

Grahic Jump Location
Stepped binder force trajectory
Grahic Jump Location
Channel forming geometry
Grahic Jump Location
Flowchart of proposed neural network control system
Grahic Jump Location
Springback angle and maximum strain versus constant binder force
Grahic Jump Location
Final part shape with increasing constant binder force
Grahic Jump Location
Punch force trajectory for 0 to 10 mm of punch travel
Grahic Jump Location
The target and actual punch force trajectories in closed-loop control
Grahic Jump Location
Resulting binder force trajectories for closed-loop control following punch force trajectory

Tables

Errata

Discussions

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In