0
TECHNICAL PAPERS

Residual Stress Measurement in a Ceramic-Metallic Graded Material

[+] Author and Article Information
Michael R. Hill, Wei-Yan Lin

Mechanical and Aeronautical Engineering Department, University of California, Davis, CA 95616e-mail: mrhill@ucdavis.edu

J. Eng. Mater. Technol 124(2), 185-191 (Mar 26, 2002) (7 pages) doi:10.1115/1.1446073 History: Received March 15, 2001; Revised August 22, 2001; Online March 26, 2002
Copyright © 2002 by ASME
Your Session has timed out. Please sign back in to continue.

References

Becker,  T. L., Cannon,  R. M., and Ritchie,  R. O., 2000, “An approximate method for residual stress calculation in functionally graded materials,” Mech. Mater., 32, No. 2, pp. 85–97.
Khor,  K. A., and Gu,  Y. W., 2000, “Effects of residual stress on the performance of plasma sprayed functionally graded ZrO2/NiCoCrAlY coatings,” Mater. Sci. Eng., A, 277, No. 1–2, pp. 64–76.
Shabana,  Y. M., and Noda,  N., 2001, “Thermo-elasto-plastic stresses in functionally graded materials subjected to thermal loading taking residual stresses of the fabrication process into consideration,” Composites, Part B, 32, No. 2, pp. 111–121.
Delfosse,  D., Cherradi,  N., and Ilschner,  B., 1997, “Numerical and experimental determination of residual stresses in graded materials,” Composites, Part B, 28, No. 1–2, pp. 127–141.
Rabin,  B. H., Williamson,  R. L. , 1998, “Residual strains in an Al2O3-Ni joint bonded with a composite interlayer: Experimental measurements and FEM analyses,” J. Am. Ceram. Soc., 81, No. 6, pp. 1541–1549.
Bokuchava,  G. D., Schreiber,  J., Shamsutdinov,  N., and Stalder,  M., 2000, “Residual stress studies in graded W/Cu materials by neutron diffraction method,” Physica B, 276, pp. 884–885.
Fukui,  Y., and Watanabe,  Y., 1996, “Analysis of thermal residual stress in a thick-walled ring of Duralcan-base Al-SiC functionally graded material,” Metall. Mater. Trans. A, 27, No. 12, pp. 4145–4151.
Cheng,  W., and Finnie,  I., 1990, “The crack compliance method for residual stress management,” Weld. World, 28, No. 516, pp. 103–110.
Prime,  M. B., 1999, “Residual stress measurement by successive extension of a slot: The crack compliance method,” Appl. Mech. Rev., 52, No. 2, pp. 75–96.
Nelson, G., and Ezis, A., 1996, “Functionally gradient material (FGM) armor in the TiB2/Ti system,” Cercom, Incorporated.
Carpenter,  R. D., Liang,  W. W., Paulino,  G. H., Gibeling,  J. C., and Munir,  Z. A., 1999, “Fracture testing and analysis of a layered functionally graded Ti/TiB beam in 3-point bending,” Mater. Sci. Forum, 308–311, pp. 837–842.
Carpenter,  R. D., Paulino,  G. H., Munir,  Z. A., and Gibeling,  J. C., 2000, “A novel technique to generate sharp cracks in metallic/ceramic functionally graded materials by reverse 4-point bending,” Scr. Mater., 43, No. 6, pp. 547–552.
Hill, M. R., Carpenter, R. D., Paulino, G. H., Munir, Z. A., and Gibeling, J. C., “Fracture testing of a layered functionally graded material,” In ASTM STP 1409 (to appear).
Lin, W-Y., 1999, “Measurement of residual stress distribution through the thickness of functionally graded material Ti/TiB2,” MS thesis. University of California, Davis, 1999.
Ritchie,  D., and Leggatt,  R. H., 1987, “Measurement of the distribution of residual stresses through the thickness of a welded joint,” Strain, 23, No. 2, pp. 61–70.
Giannakopoulos,  A. E., Suresh,  S., Finot,  M., and Olsson,  M., 1995, “Elastoplastic analysis of thermal cycling: layered materials with compositional gradients.” Acta Metall. Mater., 43, No. 4, pp. 1335–1354.
Albert, A. E., 1972, Regression and the Moore-Penrose Pseudoinverse, Academic Press, New York.
Bevington, P. R., and Robinson, D. K., 1972, Data Reduction and Error Analysis for the Physical Sciences, 2nd ed. McGraw-Hill, New York.
Strang, G. 1986, Introduction to Applied Mathematics, Wellesley-Cambridge Press, Wellesley, MA.

Figures

Grahic Jump Location
(a) Location of samples in larger FGM plate and (b) measurement locations shown with exaggerated sample irregularity
Grahic Jump Location
Coordinates and strain gage locations for the slotting experiments
Grahic Jump Location
Finite element mesh for a plane strain, symmetric model for slotting at location 7-3. Slot depth is increased by removing elements in the right-most layer in succession from top to bottom.
Grahic Jump Location
Strain release at the four slot locations, (a) Top gage, (b) bottom gage
Grahic Jump Location
Residual stress at all locations, error bars for location 8-1
Grahic Jump Location
Measured strain for location 8-1 and strain fit from a tenth order stress expansion
Grahic Jump Location
Global error in strain fit versus stress expansion order for location 8-1
Grahic Jump Location
Uncertainty in estimated stress, location 8-1, (a) Global, (b) pointwise
Grahic Jump Location
The influence of including the top gage on (a) strain-fit error and (b) stress uncertainty

Tables

Errata

Discussions

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In