0
Article

A New Quantitative Sensitivity Analysis of the Flow Stress of 18 Engineering Materials in Machining

[+] Author and Article Information
N. Fang

Department of Mechanical and Aerospace Engineering, Utah State University, Logan, UT 84322-4130

J. Eng. Mater. Technol 127(2), 192-196 (Apr 06, 2005) (5 pages) doi:10.1115/1.1857935 History: Received December 22, 2003; Revised October 15, 2004; Online April 06, 2005
Copyright © 2005 by ASME
Your Session has timed out. Please sign back in to continue.

References

Shirakashi,  T., and Obikawa,  T., 1998, “Recent Progress and Some Difficulties in Computational Modeling of Machining,” Mach. Sci. Technol., 2, pp. 277–301.
Liu,  C. R., and Guo,  Y. B., 2000, “Finite Element Analysis of the Effect of Sequential Cuts and Tool-Chip Friction on Residual Stresses in a Machined Layer,” Int. J. Mech. Sci., 42, pp. 1069–1086.
Shih,  A. J., 1996, “Finite Element Analysis of the Rake Angle Effects on Orthogonal Metal Cutting,” Int. J. Mech. Sci., 38, pp. 1–17.
Stevenson,  R., 1997, “Study on the Correlation of Workpiece Mechanical Properties from Compression and Cutting Tests,” Mach. Sci. Technol., 1, pp. 67–79.
Stephensen,  D. A., 1989, “Material Characterization for Metal-Cutting Modeling,” ASME J. Eng. Mater. Technol., 111, pp. 210–219.
Fang,  N., 2003, “Slip-Line Modeling of Machining with a Rounded-Edge Tool, Part I: New Model and Theory,” J. Mech. Phys. Solids, 51, pp. 715–742.
Fang,  N., Jawahir,  I. S., and Oxley,  P. L. B., 2001, “A Universal Slip-Line Model With Non-Unique Solutions for Machining With Curled Chip Formation and a Restricted Contact Tool,” Int. J. Mech. Sci., 43, pp. 557–580.
van Luttervelt,  C. A., Childs,  T. H. C., Jawahir,  I. S., Klocke,  F., and Venuvinod,  P. K., 1998, “Present Situation and Future Trends in Modeling of Machining Operations,” CIRP Ann., 47, pp. 587–626.
Kececioglu,  D., 1958, “Shear-Strain Rate in Metal Cutting and Its Effects on Shear-Flow Stress,” Trans. ASME, 80, pp. 158–168.
Kececioglu,  D., 1958, “Shear-Zone Temperature in Metal Cutting and Its Effects on Shear-Flow Stress,” Trans. ASME, 80, pp. 541–546.
Kececioglu,  D., 1960, “Shear-Zone Size, Compressive Stress, and Shear Strain in Metal-Cutting and Their Effects on Mean Shear-Flow Stress,” ASME J. Eng. Ind., 82, pp. 79–86.
Spaans,  C., 1972, “A Treatise on the Streamlines and the Stress, Strain, and Strain Rate Distribution, and on Stability in the Primary Shear Zone in Metal Cutting,” ASME J. Eng. Ind., 94, pp. 690–696.
Murarka,  P. D., Hinduja,  S., and Barrow,  G., 1981, “Influence of Strain, Strain-Rate and Temperature on the Flow Stress in the Primary Deformation Zone in Metal Cutting,” Int. J. Mach. Tool Des. Res., 21, pp. 207–216.
Saltelli, A., Chan, K., and Scott, E. M., 2000, Sensitivity Analysis, Wiley, Chichester, UK.
Johnson, G. R., and Cook, W. H., 1983, “A Constitutive Model and Data for Metals Subjected to Large Strains, High Strain Rates and High Temperatures,” Proc. of 7th Int. Symp. Ball., Hague, The Netherlands, pp. 541–547.
Jaspers, S. P. F. C., 1999, “Metal Cutting Mechanics and Material Behavior,” Ph.D. thesis, Technical University of Eindhoven, Eindhoven, The Netherlands.
Oxley, P. L. B., 1989, The Mechanics of Machining: An Analytical Approach to Assessing Machinability, Ellis Horwood Limited, Chichester, UK.
Zerilli,  F. J., and Armstrong,  R. W., 1987, “Dislocation-Mechanics-Based Constitutive Relations for Material Dynamics Calculations,” J. Appl. Phys., 61, pp. 1816–1825.
Maekawa,  K., Shirakashi,  T., and Usui,  E., 1983, “Flow Stress of Low Carbon Steel at High Temperature and Strain Rate (Part 2)–Flow Stress Under Variable Temperature and Variable Strain Rate,” Bull. Jpn. Soc. Precis. Eng., 17, pp. 167–172.
Childs, T. H. C., 1998, “Material Property Needs in Modeling Metal Machining,” Proc. CIRP Int. Work. Model. Mach. Opera., Atlanta, pp. 193–202.
Stevenson,  M. G., and Oxley,  P. L. B., 1970–1971, “An Experimental Investigation of the Influence of Strain-Rate and Temperature on the Flow Stress Properties of a Low Carbon Steel Using a Machining Test,” Proc. Inst. Mech. Eng., 185, pp. 741–754.
Friedman,  J. H., 1991, “Multivariate Adaptive Regression Splines,” Ann. Stat., 19, pp. 1–67.
http://www.salford-systems.com
Johnson, G. R., Stryk, R. A., Holmquist, T. J., and Beissel, S. R., 1996, User Instructions for the 1996 Version of the EPIC Code, Alliant Techsystems Inc.
Dannemann, K. A., Anderson, C. E., and Johnson, G. R., 2001, “Modeling the Ballistic Impact Performance of Two Aluminum Alloys,” Proc. Symp. Model. Perf. Eng. Struct. Mate. II, Indianapolis, pp. 63–74.

Figures

Grahic Jump Location
Comparison of four material constitutive models
Grahic Jump Location
Sensitivity analysis of the flow stress of six representative materials
Grahic Jump Location
Material flow stress for three materials (T=300°C)

Tables

Errata

Discussions

Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In