RESEARCH PAPERS: Special Issue on Time-Dependent Behaviors of Polymer Matrix Composites and Polymers

Buckling Analysis of Delaminated and Stitched Composite Plate System Under Hygrothermal Pressure

[+] Author and Article Information
S. Leigh Phoenix1

Department of Theoretical and Applied Mechanicsslp6@cornell.edu

A. Kadir Yavuz

Department of Theoretical and Applied Mechanics

Katerina D. Papoulia

School of Civil and Environmental Engineering

C. Yuen Hui

Department of Theoretical and Applied Mechanics, Cornell University, Ithaca, NY 14853


Author to whom all correspondence should be addressed.

J. Eng. Mater. Technol 128(1), 117-122 (May 13, 2005) (6 pages) doi:10.1115/1.2128428 History: Received February 02, 2005; Revised May 13, 2005

In this study, we develop a model for buckling of a partially delaminated composite plate with transverse stitching to resist out of plane deformations. The model applies to carbon fiber/polyimide matrix composites rapidly heated to around 370 °C, where it is known that steam-induced delamination (the popcorn effect) becomes an issue as the pressures generated approach the tensile strength of the matrix. Thus, a key element is the incorporation of this hygrothermal pressure within the formulation. This complex composite structure is modeled as two adhesively connected, specially orthotropic, rectangular plates, and the delaminations with internal vapor pressure are considered as holes in the adhesive layer. The intact regions of the adhesive layer and the stitches are modeled by continuous and discrete linear mechanical springs, respectively. The energy contributions of each component in the system are expressed in terms of out-of-plane displacements. The boundary conditions are that the system is simply supported along all edges so as to permit a Fourier sine series to approximate the transverse displacements. Application of the energy minimization approach gives a system of algebraic equations to determine the unknown weighting coefficients of the functions describing the transverse deflections of each plate layer. Deformed shapes of the system under axial compressive loads are obtained for different hygrothermally induced pressure conditions so as to show that the model works well. Parametric studies on critical buckling loads are performed for a few stitch and delamination configurations. It is found that stitching through delaminated areas can increase critical buckling loads and alter the sequence of corresponding mode shapes.

Copyright © 2006 by American Society of Mechanical Engineers
Your Session has timed out. Please sign back in to continue.



Grahic Jump Location
Figure 1

General system configuration

Grahic Jump Location
Figure 2

Delamination and stitch locations

Grahic Jump Location
Figure 3

Deformations (in meters) of the system (a) without stitching and (b) with one stitch

Grahic Jump Location
Figure 4

Nondimensionalized critical buckling loads versus horizontal locations of the stitch (xs,0) for two different radii of delaminations

Grahic Jump Location
Figure 5

Nondimensional critical buckling loads versus radius of delamination (rd) located at the center point (0.1,0.1) of the plate system

Grahic Jump Location
Figure 6

First symmetric buckling mode shapes of the plate system with one center delamination (a) without stitching and (b) with one stitch at xs=0.02m

Grahic Jump Location
Figure 7

(a) First (b) second (c) third, and (d) fourth anti-symmetric buckling mode shapes of the plate system with one center delamination with one stitch (xs=0.02m) and without stitches (stitches do not affect anti-symmetric modes)



Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In