Discussion: “On the Reference Length and Mode Mixity for a Bimaterial Interface” (, and , 2007, ASME J. Eng. Mater. Technol., 129, pp. 580–587) PUBLIC ACCESS

[+] Author and Article Information
Vladislav Mantič

Group of Elasticity and Strength of Materials, School of Engineering, University of Seville, Sevilla 41092, Spainmantic@esi.us.es

J. Eng. Mater. Technol 130(4), 045501 (Sep 17, 2008) (2 pages) doi:10.1115/1.2975231 History: Received January 09, 2008; Revised August 01, 2008; Published September 17, 2008

In a recent paper (1), the authors revisited a basic question of interfacial fracture mechanics, namely, the choice of the characteristic reference lengthlc in the open model of interface cracks (2), and introduced a new procedure for an estimation of lc based on the interface fracture toughness measurements. It is well known that the choice of a reference length l is related to the position along the abscissa axis of the interface fracture toughness curve for an elastic bimaterial, which represents the interfacial fracture toughness Γint(ψ) as a function of the local phase angle ψ of the stress intensity factor (3). The following two comments are essential with regard to the procedure for an estimation of lc proposed by the authors in Sec. 3.2 and applied to their experimental results in Sec. 5.

First Comment. The procedure introduced by the authors tacitly assumes that the hypothetical interface fracture toughness curve is symmetric with respect to a vertical axis. However, a certain asymmetry of toughness curves for some bimaterials has been indicated by several toughness measurements (4-6) and also by numerical predictions (7). Such an asymmetry is associated with different crack tip morphologies (8), with a tendency to opening or closing crack faces at a crack tip and to different shapes and volumes of the near-tip plastic zones (4,7) corresponding to the opposite signs of ψ.

In the case of an asymmetric toughness curve, the procedure introduced may lead to a misinterpretation of the experimental interface fracture toughness measurements, which will be briefly illustrated in the following. Fracture toughness measurements obtained by two different specimen configurations, such as those used by the authors (1) (denoted as A and B specimens), can be represented on a unique toughness curve if the same orientation of the axes of the local coordinate system (x,y) with respect to each material (aluminum and vinyl ester in Ref. 1) is considered in each configuration (see Fig. 1). The relevant issue in Fig. 1 is the sign of ψ1 associated with the reference length l1. Let ρI denote the distance from the crack tip to the first interpenetration point (9-10). Then, it is noteworthy to mention that in Configuration A, e.g., ρI3.7×107μm (the interpenetration zone is of subatomic size, thus being physically meaningless) for ψ1=45deg, whereas in Configuration B, e.g., ρI2.7μm (indicating a possibly physically relevant contact between the crack faces) for ψ1=45deg.

Now, in light of Fig. 1, the procedure introduced by the authors can be easily interpreted, as schematically shown in Fig. 2. Due to a different coordinate system used for A specimens, the toughness curve is mirrored with respect to the ordinate axis (Fig. 2). After evaluation of lc, both toughness curves, in Figs.  22 are translated by an angle of magnitude ψ0=εln(lc/l1), resulting in two relatively close but different toughness curves (see Fig. 2), which should not be interpreted as a unique toughness curve, as was done in Fig. 6 in Ref. 1.

Second Comment. In the case of a symmetric toughness curve for a bimaterial, the characteristic reference length lc, estimated by the procedure introduced by the authors, leads to the toughness curve Γint(ψc), which is symmetric with respect to the ordinate axis and achieves its minimum for ψc=0 deg. This fact is illustrated schematically in Fig. 3, where it is seen that the distance between the original and the mirrored toughness curves is 2ψ0, ψ0 giving the position of the minimum of the toughness curve. Translating each curve by an angle of magnitude ψ0=εln(lc/l1) results in a unique toughness curve, as done correctly in Fig. 6 in Ref. 1.

Summarizing, the value of lc estimated by the procedure introduced in Ref. 1 has a clear physical meaning, but only in the case of interface fracture toughness curves which are symmetric with respect to a vertical axis.


Copyright © 2008 by American Society of Mechanical Engineers
This article is only available in the PDF format.



Grahic Jump Location
Figure 1

Local configurations of A and B specimens in Ref. 1, and a hypothetical asymmetric interface fracture toughness curve with the experimental results from Ref. 1

Grahic Jump Location
Figure 2

(a) Mirrored toughness curve for A specimens, (b) toughness curve for B specimens, and (c) translated toughness curves by the procedure introduced in Ref. 1

Grahic Jump Location
Figure 3

(a) Hypothetical symmetric toughness curve, (b) Mirrored and original toughness curves and the resultant toughness curve obtained by the procedure introduced in Ref. 1




Some tools below are only available to our subscribers or users with an online account.

Related Content

Customize your page view by dragging and repositioning the boxes below.

Related Journal Articles
Related eBook Content
Topic Collections

Sorry! You do not have access to this content. For assistance or to subscribe, please contact us:

  • TELEPHONE: 1-800-843-2763 (Toll-free in the USA)
  • EMAIL: asmedigitalcollection@asme.org
Sign In