One of the remedies to reduce the major emissions production of nitric oxide carbon monoxide (CO), and unburned hydrocarbon (UHC) from conventional gas turbine engine combustors at both high and low operating conditions without losing performance and stability is to use variable geometry combustors. This type of combustor configuration provides the possibility of dynamically controlling the airflow distribution of the combustor based on its operating conditions and therefore controlling the combustion in certain lean burn conditions. Two control schemes are described and analyzed in this paper: Both are based on airflow control with variable geometry, the second including fuel staging. A model two-spool turbofan engine is chosen in this study to test the effectiveness of the variable geometry combustor and control schemes. The steady and dynamic performance of the turbofan engine is simulated and analyzed using an engine transient performance analysis code implemented with the variable geometry combustor. Empirical correlations for CO, and UHC are used for the estimation of emissions. Some conclusions are obtained from this study: (1) with variable geometry combustors significant reduction of emissions at high operating conditions and CO and UHC at low operating condition is possible; (2) combustion efficiency and stability can be improved at low operating conditions, which is symbolized by the higher flame temperature in the variable geometry combustor; (3) the introduced correlation between nondimensional fuel flow rate and air flow ratio to the primary zone is effective and simple in the control of flame temperature; (4) circumferential fuel staging can reduce the range of air splitter movement in most of the operating conditions from idle to maximum power and have the great potential to reduce the inlet distortion to the combustor and improve the combustion efficiency; and (5) during transient processes, the maximum moving rate of the hydraulic driven system may delay the air splitter movement but this effect on engine combustor performance is not significant.
Skip Nav Destination
Article navigation
October 2003
Technical Papers
Steady and Dynamic Performance and Emissions of a Variable Geometry Combustor in a Gas Turbine Engine
Y. G. Li,
Y. G. Li
School of Engineering, Cranfield University, Bedford MK43 0AL, England
Search for other works by this author on:
R. L. Hales
R. L. Hales
School of Engineering, Cranfield University, Bedford MK43 0AL, England
Search for other works by this author on:
Y. G. Li
School of Engineering, Cranfield University, Bedford MK43 0AL, England
R. L. Hales
School of Engineering, Cranfield University, Bedford MK43 0AL, England
Contributed by the International Gas Turbine Institute (IGTI) of THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS for publication in the ASME JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER. Paper presented at the International Gas Turbine and Aeroengine Congress and Exhibition, Amsterdam, The Netherlands, June 3–6, 2002; Paper No. 2002-GT-30135. Manuscript received by IGTI, December 2001, final revision, March 2002. Associate Editor: E. Benvenuti.
J. Eng. Gas Turbines Power. Oct 2003, 125(4): 961-971 (11 pages)
Published Online: November 18, 2003
Article history
Received:
December 1, 2001
Revised:
March 1, 2002
Online:
November 18, 2003
Citation
Li , Y. G., and Hales , R. L. (November 18, 2003). "Steady and Dynamic Performance and Emissions of a Variable Geometry Combustor in a Gas Turbine Engine ." ASME. J. Eng. Gas Turbines Power. October 2003; 125(4): 961–971. https://doi.org/10.1115/1.1615253
Download citation file:
Get Email Alerts
Cited By
On Leakage Flows In A Liquid Hydrogen Multi-Stage Pump for Aircraft Engine Applications
J. Eng. Gas Turbines Power
A Computational Study of Temperature Driven Low Engine Order Forced Response In High Pressure Turbines
J. Eng. Gas Turbines Power
The Role of the Working Fluid and Non-Ideal Thermodynamic Effects on Performance of Gas Lubricated Bearings
J. Eng. Gas Turbines Power
Tool wear prediction in broaching based on tool geometry
J. Eng. Gas Turbines Power
Related Articles
Advanced Catalytic Pilot for Low NO x Industrial Gas Turbines
J. Eng. Gas Turbines Power (October,2003)
Autoignition of Hydrogen and Air Inside a Continuous Flow Reactor With Application to Lean Premixed Combustion
J. Eng. Gas Turbines Power (September,2008)
25 Years of BBC/ABB/Alstom Lean Premix Combustion Technologies
J. Eng. Gas Turbines Power (January,2007)
Performance of a Reduced NO x Diffusion Flame Combustor for the MS5002 Gas Turbine
J. Eng. Gas Turbines Power (April,2000)
Related Proceedings Papers
Related Chapters
Outlook
Closed-Cycle Gas Turbines: Operating Experience and Future Potential
Introduction
Consensus on Operating Practices for Control of Water and Steam Chemistry in Combined Cycle and Cogeneration
A Simple Carburetor
Case Studies in Fluid Mechanics with Sensitivities to Governing Variables