This paper presents the results of an experimental investigation of the nondestructive inspection (NDI) of cracks in an intermediate scale tubular T-joint similar to those used in offshore platforms. To simulate the real situation, cracks were generated under fatigue loading. Modal testing and analysis were then carried out to study the vibration characteristics of the tubular T-joints. Strain gages were used as the main transducers to acquire data because strains are more sensitive to the presence of cracks. Strain frequency response functions were particularly analyzed. Three salient phenomena were observed: (a) antiresonance shifts, (b) quasi-static phenomenon, and (c) nonlinearity, all of which are indicative of the presence of cracks, even at a normalized crack size (the ratio of cracking area to load-bearing area) as small as 0.07. Therefore, the method developed in this study renders a more promising NDI technique than the frequency monitoring technique. Finite element analyses were also conducted to confirm the experimental results and to depict the mode shapes.
Issue Section:
Research Papers
1.
ABAQUS Manual, 1995, Hibbitt, Karlsson & Sorensen, Inc.
2.
Adams
R. D.
Cawley
P.
Pye
C. J.
Stone
B. J.
1978
, “A Vibration Technique for Non-Destructively Assessing the Integrity of Structures
,” Journal of Mechanical Engineering Science
, Vol. 20
, No. 2
, pp. 93
–100
.3.
Bayliss, M., Short, D., and Bax, M., 1988, Underwater Inspection, London, E. & F. N. Spon Ltd, London, U.K.
4.
Bray, D. E., and McBride, D., 1992, Nondestructive Testing Techniques, John Wiley & Sons, Inc., New York, NY.
5.
Cawley
P.
Adams
R. D.
1979
, “The Locations of Defects in Structures from Measurements of Natural Frequencies
,” Journal of Strain Analysis
, Vol. 14
, No. 2
, pp. 49
–57
.6.
Cheng, S. M., 1998, “Non-Destructive Evaluation of Cracking in Tubular T-Joints Using Vibration Procedures,” Ph.D. thesis, Faculty of Engineering and Applied Science, Memorial University of Newfoundland, St. John’s, NF, Canada, p. 338.
7.
Cheng
S. M.
Swamidas
A. S. J.
Wallace
W.
Wu
X. J.
1999
, “An Experimental Investigation of Tubular T-joints Under Cyclic Loads
,” ASME JOURNAL OF OFFSHORE MECHANICS AND ARCTIC ENGINEERING
, Vol. 121
, Aug., pp. 137
–143
.8.
Chen
Y.
Swamidas
A. S. J.
1993
, “Change of Modal Parameters due to Crack Growth in a Tripod Tower Platform
,” Canadian Journal of Civil Engineering
, Oct., Vol. 20
, No. 5
, pp. 801
–813
.9.
Collins
K. R.
Plaut
R. A.
Waner
J.
1992
, “Free and Forced Vibration of a Cantilever Bar with a Crack
,” ASME Journal of Vibration and Acoustics
, Vol. 114
, Apr., pp. 171
–177
.10.
Dimarogonas
A. D.
Chondros
T. G.
1980
, “Identification of Cracks in Welded Joints of Complex Structures
,” Journal of Sound and Vibration
, Vol. 69
, No. 4
, pp. 531
–538
.11.
Doug, C., Zhang, P. Q., Feng, W. Q., and Huang, T. C., 1994, “The Sensitivity study of the Modal Parameters of a Cracked Beam,” Proceedings, 12th International Modal Analysis Conference, Vol. 1, pp. 98–104.
12.
Friswell, M. I., and Penny, J. E. T., 1992, “A Simple Nonlinear Model of a Cracked Beam,” Proceedings, 10th International Modal Analysis Conference, Vol. 1, pp. 516–521.
13.
Gomes, A. J. M. A., and Silva, J. M. M. E., 1990, “On the Use of Modal Analysis for Crack Identification,” Proceedings, 8th International Modal Analysis Conference, Vol. 2, pp. 1108–1115.
14.
Gomes, A. J. M. A., and Silva, J. M. M. E., 1991, “Theoretical and Experimental Data on Crack Depth Effects in the Dynamic Behavior of Free-Free Beams,” Proceedings, 9th International Modal Analysis Conference, Vol. 1, pp. 274–283.
15.
He
J.
Ewins
D. J.
1986
, “Analytical Stiffness Matrix Correction Using Measured Vibration Modes
,” International Journal of Analytical and Experimental Modal Analysis
, Vol. 1
, No. 3
, pp. 1
–9
.16.
Newman, J. C., Jr., and Elber, W., eds., 1988, Machanics of Fatigue Crack Closure, Allison, J. E. et al. “A Comparison of Measurement Methods and Numerical Procedures for the Experimental Characterization of Fatigue Crack Closure,” ASTM, Philadelphia, PA.
17.
Pandey
A. K.
Biswas
M.
Samman
M. M.
1991
, “Damage Detection from Changes in Curvature Mode Shapes
,” Journal of Sound and Vibration
, Vol. 145
, No. 2
, pp. 321
–332
.18.
Pandey
A. K.
Biswas
M.
1994
, “Damage Detection in Structures Using Changes in Flexibility
,” Journal of Sound and Vibration
, Vol. 169
, No. 2
, pp. 3
–17
.19.
Prime, M. B., and Shevitz, D. W., 1996, “Linear and Nonlinear Methods for Detecting Cracks in Beams,” Proceedings, 14th International Modal Analysis Conference, pp. 1437–1443.
20.
Richardson, M. H., and Mannan, M. A., 1991, “Determination of Modal Sensitivity Functions for Location of Structural Faults,” Proceedings, 9th International Modal Analysis Conference, Vol. 1, pp. 670–676.
21.
Rytter, A., 1993, Vibrational Based Inspection of Civil Engineering Structures, Ph. D. Thesis, Paper No. 44, Department of Building Technology and Structural Engineering, The University of Aalborg, Sohngaardsholmsvej 57, DK 9000, ISSN 0902-7513 R9314, May.
22.
Sekhar
A. S.
Prabhu
B. S.
1992
, “Crack Detection and Vibration Characteristics of Cracked Shafts
,” Journal of Sound and Vibration
, Vol. 157
, No. 2
, pp. 375
–381
.23.
Srinivasan, M. G., and Kot, C. A., 1992, “Effects of Damage on the Modal Parameters of a Cylindrical Shell,” Proceedings, 10th International Modal Analysis Conference, pp. 529–535.
24.
Structural Measurement System, 1994, STAR, Santa Clara, CA.
25.
Wang, W., 1987, “Sensitivity Analysis in Fault Vibration Diagnosis of Structures,” Proceedings, 5th International Modal Analysis Conference, Vol. 1, pp. 496–501.
26.
Wardenier, J., and Shahi, E. P., 1991, “Tubular Structures,” Proceedings, 4th International Symposium, Delft University Press, Delft, the Netherlands.
27.
West, W. M., 1984, “Illustration of the Use of Modal Assurance Criterion to Detect Structural Changes in an Orbiter Test Specimen,” Proceedings, Air Force Conference on Aircraft Structural Integrity, pp. 1–6.
28.
Zhang, Z., and Aktan, A. E., 1995, “The Damage Indices for Constructed Facilities,” Proceedings, 13th International Modal Analysis Conference, pp. 1520–1529.
This content is only available via PDF.
Copyright © 1999
by The American Society of Mechanical Engineers
You do not currently have access to this content.
