The main purpose of the present paper is to investigate the effect of crosshead speed, specimen thickness, and welding on the fracture toughness. The material of the investigated pipe is a high density polyethylene (HDPE), which is commonly used in natural gas piping systems. The welding technique used in this study is butt-fusion (BF) welding technique. The crosshead speed ranged from 5 to 500 mm/min and specimen thickness ranged from 9 to 45 mm for both welded and unwelded specimens at room temperature, Ta = 20 °C. Curved three point bend (CTPB) specimens were used to determine KQ. Furthermore, the results of fracture toughness, KQ, will be compared with the plane–strain fracture toughness, JIC, for welded and unwelded specimens. The experimental results revealed that KQ increases with increasing the crosshead speed, while KQ decreases as the specimen thickness increases. The investigation reveals that the apparent fracture toughness, KQ, for HDPE pipe of unwelded specimen is greater than that of corresponding value for welded specimen. The same trend was observed for the plane-strain fracture toughness, JIC. At lower crosshead speeds there is a minimum deviation in KQ between welded and unwelded specimens, while the deviation becomes larger with increasing crosshead speed.
Issue Section:
Materials and Fabrication
References
1.
Chen
, H.
, Scavuzzo
, R. J.
, and Srivatsan
, T. S.
, 1997
, “Influence of Joining on the Fatigue and Fracture Behavior of High Density Polyethylene Pipe
,” J. Mater. Sci. Perform.
, 6
(4
), pp. 473
–480
.10.1007/s11665-997-0119-82.
Zhao
, J. Q.
, Daigle
, L.
, and Beaulieu
, D.
, 2002
, “Effect of Joint Contamination on the Quality of Butt-Fused High-Density Polyethylene (HDPE) Pipe Joints
,” Can. J. Civ. Eng.
, 29
(5
), pp. 787
–798
.10.1139/l02-0783.
Daigle
, L.
, Zhao
, J. Q.
, and Beaulieu
, D.
, 2003
, “Innovative Approach to Testing the Quality of Fusion Joints
,” Plast., Rubber Compos.
, 32
(8–9
), pp. 385
–395
.10.1179/1465801032250041534.
El-Bagory
, T. M. A. A.
, Sallam
, H. E. M.
, Younan
, M. Y. A.
, and Abdel-Latif
, L. A.
, 2014
, “Limit Load Determination and Material Characterization of Cracked Polyethylene Miter Pipe Bends
,” ASME J. Pressure Vessel Technol.
, 136
(4
), p. 041203
.10.1115/1.40263305.
Roberts
, D. R.
, Mandell
, J. F.
, and McGarry
, F. J.
, 1981
, “Applicability of Plane Strain Fracture Toughness Testing Techniques to Polyethylene Pipe Materials
,” MIT TAP, Research Report No. R81-3.6.
Roberts
, D. R.
, Darwish
, A.
, Mandell
, J. F.
, McGarry
, F. J.
, and Roylance
, D. K.
, 1979
, “Fracture Toughness Testing of Polyvinyl Chloride and High Density Polyethylene Pipe
,” Technology Adaptation Program, Massachusetts Institute of Technology, Cambridge, MA, Report No. R79-3.7.
Chan
, M. K. V.
, and Williams
, J. G.
, 1983
, “J-Integral Studies of Crack Initiation of a Tough High Density Polyethylene
,” Int. J. Fract.
, 23
(2
), pp. 145
–159
.8.
O'Connell
, P. A.
, Duckett
, R. A.
, and Ward
, I. M.
, 2002
, “Brittle–Ductile Transitions in Polyethylene
,” Polym. Eng. Sci.
, 42
(7
), pp. 1493
–1508
.10.1002/pen.110469.
Gensler
, R.
, Plummer
, C. J. G.
, Grein
, C.
, and Kausch
, H.-H.
, 2000
, “Influence of the Loading Rate on the Fracture Resistance of Isotactic Polypropylene and Impact Modified Isotactic Polypropylene
,” Polymer
, 41
(10
), pp. 3809
–3819
.10.1016/S0032-3861(99)00593-510.
Mandell
, J. F.
, Roberts
, D. R.
, and McGarry
, F. J.
, 1983
, “Plane Strain Fracture Toughness of Polyethylene Pipe Materials
,” Polym. Eng. Sci.
, 23
(7
), pp. 404
–411
.10.1002/pen.76023070711.
Kapp
, J. A.
, Pflegl
, G. A.
, and Underwood
, J. H.
, 1977
, “The Effect of Wall Thickness Variation of KI for the Proposed C-Shaped Specimen
,” Int. J. Fract.
, 13
(5
), pp. 721
–724
.10.1007/BF0001730912.
Jones
, A. T.
, 1974
, “Fracture Toughness Testing With Section of Cylinders
,” Eng. Fract. Mech.
, 6
(4
), pp. 653
–662
.10.1016/0013-7944(74)90064-213.
Chan
, M. K. V.
, and Williams
, J. G.
, 1981
, “Plane Strain Fracture Toughness Testing of High Density Polyethylene
,” Polym. Eng. Sci.
, 21
(5
), pp. 1019
–1026
.10.1002/pen.76021150814.
Lee
, B. Y.
, Kim
, J. S.
, Lee
, S. K.
, and Kim
, Y. K.
, 2012
, “Butt-Welding Technology for Double Walled Polyethylene Pipe
,” Mater. Des.
, 35
, pp. 626
–632
.10.1016/j.matdes.2011.10.01415.
Leskovics
, K.
, Kollár
, M.
, and Bárczy
, P.
, 2006
, “A Study of Structure and Mechanical Properties of Welded Joints in Polyethylene Pipes
,” Mater. Sci. Eng.: A
, 419
(1–2
), pp. 138
–143
.10.1016/j.msea.2005.12.01916.
Pfeil
, M. C.
, Kenner
, V. H.
, and Popelar
, C. H.
, 1993
, “A Fracture Mechanics Evaluation for the Life Expectancy of Polyethylene Butt Fusion Joints
,” Eng. Fract. Mech.
, 44
(1
), pp. 91
–107
.10.1016/0013-7944(93)90084-617.
El-Bagory
, T. M. A. A.
, Sallam
, H. E. M.
, and Younan
, M. Y. A.
, 2014
, “Effect of Strain Rate, Thickness, Welding on the J–R Curve for Polyethylene Pipe Materials
,” Theor. Appl. Fract. Mech.
, 74
, pp. 164
–180
.10.1016/j.tafmec.2014.09.00818.
ASTM Standard F714-13, “
Standard Specification for Polyethylene (PE) Plastic Pipe (SDR-PR) Based on Outside Diameter
,” Annual Book of ASTM Standards, Vol. 08.04, American Society for Testing and Materials, ASTM International, West Conshohocken, PA.19.
ASTM Standard D3035–12e1, “
Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter
,” Annual Book of ASTM Standards, Vol. 08.04, American Society for Testing and Materials, ASTM International, West Conshohocken, PA.20.
Potente
, H.
, and Tappe
, P.
, 1985
, “Heated Tool–Butt Welding of Polyethylene-Pipes—Welding Parameters and Testing Technique
,” Mater. Des.
, 5
(6
), pp. 273
–280
.10.1016/0261-3069(85)90112-821.
Stokes
, V. K.
, 1998
, “Experiments on the Hot-Tool Welding of Three Dissimilar Thermoplastics
,” Polymer
, 39
(12
), pp. 2469
–2477
.10.1016/S0032-3861(97)00569-722.
DVS 2207-1:2014-07,
Welding of Thermoplastics—Heated Tool Welding of Pipes, Pipeline Components and Sheets Made of PE
, DIN Deutsches Institut für Normung e. V., Berlin, Germany.23.
ASTM Standard E399-12e3, “Standard Test Method for Linear-Elastic Plane-Strain Fracture Toughness KIC of Metallic Materials,” Annual Book of ASTM Standards, Vol. 03.01, Metals Mechanical Testing; Elevated and Low Temperature Tests; Metallography, American Society for Testing and Materials, ASTM International, West Conshohocken, PA.
24.
ASTM Standard D5045-99(2007)e1, “Standard Test Methods for Plane-Strain Fracture Toughness and Strain Energy Release Rate of Plastic Materials,” Annual Book of ASTM Standards, Vol. 8.03, American Society for Testing and Materials, ASTM International, West Conshohocken, PA.
25.
Kaufman
, J. G.
, 1977
, “Experience in Plane-Strain Fracture Toughness Testing per ASTM Method E–399
,” Development in Fracture Mechanics Test Methods Standardization, ASTM STP 632
, W. F.
Brown
, Jr., and J. G.
Kaufman
, eds., American Society for Testing and Materials, ASTM International
, West Conshohocken, PA
, pp. 3
–24
.26.
Ewalds
, H. L.
, and Wanhill
, R. J. H.
, 1984
, Fracture Mechanics
, Krips Repro
, Meppel, The Netherlands
.27.
Flueler
, P.
, Mandell
, J. F.
, and McGarry
, F. J.
, 1978
, “Preliminary Study of the Applicability of Plane Strain Fracture Toughness Test Techniques to Plastic Pipe Materials
,” Technological Planning Program, Cairo University/Massachusetts Institute of Technology, TAP Report No. 79.1.28.
El-Bagory
, T. M. A. A.
, Sallam
, H. E. M.
, and Younan
, M. Y. A.
, 2013
, “Mechanical Behavior of Welded and Unwelded Polyethylene Pipe Materials
,” ASME
Paper No. PVP2013-97743.10.1115/PVP2013-97743Copyright © 2015 by ASME
You do not currently have access to this content.
