1-20 of 76
Keywords: creep
Close
Sort by
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Pressure Vessel Technol. December 2022, 144(6): 061506.
Paper No: PVT-22-1023
Published Online: June 10, 2022
...Markian Petkov; George A. Young; Pierre-Alexandre Juan Future Gen IV high-temperature reactors are expected to operate above 450 °C where creep effects are significant in safety-related structures, e.g., reactor vessels. The ASME Boiler and Pressure Vessel Code (BPVC) Section III Division 5...
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Pressure Vessel Technol. October 2022, 144(5): 051307.
Paper No: PVT-21-1130
Published Online: February 16, 2022
... load lower bound pressure vessel power law creep A new and improved method to determine statically admissible stress distributions in mechanical components and structures, and limit loads thereof, is introduced in Part 1 of this article. This method, called the bounded elastic moduli...
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Pressure Vessel Technol. October 2022, 144(5): 051306.
Paper No: PVT-21-1129
Published Online: February 16, 2022
... vessel power law creep Before the advent of high-speed computers and finite element software, determination of exact limit loads of structures was difficult when compared to the relative ease of calculating the respective bounds. The classical lower bound theorem [ 1 ] states that the limit...
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Pressure Vessel Technol. February 2022, 144(1): 011507.
Paper No: PVT-20-1287
Published Online: November 8, 2021
... temperature that causes degradation of material properties. Pressure reducing valve is an important component being employed within a main steam line of the supercritical boiler, which occasionally thermal-fatigue failure being reported. This research has investigated creep-cyclic plastic behavior...
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Pressure Vessel Technol. February 2022, 144(1): 011504.
Paper No: PVT-20-1286
Published Online: October 8, 2021
... accident. The materials used previously for SG tubes around the world have been replaced and will be replaced by Alloy 690 given its improved corrosion resistance relative to that of Alloy 600. However, studies of the high-temperature creep and creep-rupture characteristics of SG tubes made of Alloy 690...
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Pressure Vessel Technol. February 2021, 143(1): 011503.
Paper No: PVT-19-1251
Published Online: August 5, 2020
...Cheng Gong; Fu-Hai Gao; Jian-Guo Gong; Fu-Zhen Xuan An accurate stress estimation for creep evaluation is essential for the long-term safe operation of components at elevated temperature. In general, the section-dependent parameter K t is defined in elastic analysis routine to account...
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Pressure Vessel Technol. December 2020, 142(6): 061502.
Paper No: PVT-19-1205
Published Online: June 10, 2020
...Tian-Ye Niu; Cheng Gong; Jian-Guo Gong; Fu-Zhen Xuan Notched structures widely exist in steam turbine components in fossil power plant, e.g., the groove of the rotor, etc. Previous studies indicate that creep failures occur at the groove of the rotor or the adjacent regions. Thus, it is essential...
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Pressure Vessel Technol. August 2020, 142(4): 041701.
Paper No: PVT-19-1146
Published Online: April 8, 2020
...Tian-Ye Niu; Cheng Gong; Jian-Guo Gong; Fu-Zhen Xuan; Haofeng Chen Geometrical discontinuities (such as holes and grooves) widely exist in many components, which operate at elevated temperatures. Creep assessment of the geometrical discontinuities is essential for the safe operation of the system...
Topics: Creep, Steel, Stress
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Pressure Vessel Technol. December 2019, 141(6): 061406.
Paper No: PVT-18-1197
Published Online: September 20, 2019
...Lin Zhu; Xinbao Liu; Ping Fan; Jianqiu Liu; Chengfei Pan Over the range of variables (temperature and stress) normally encountered in service applications, creep behaviors of 9Cr-1Mo steel were investigated with various models, such as Wilshire model, combination of exponential form and omega (CEO...
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Pressure Vessel Technol. December 2019, 141(6): 061201.
Paper No: PVT-17-1235
Published Online: August 2, 2019
... in standardized relaxation tests. Within this work, a loss in bolt pretension of up to almost 50% over a comparatively short period of experimental time was observed. By means of numerical calculations, creep deformation in the transition areas between pipe and flange plate sections was identified to be a major...
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Pressure Vessel Technol. April 2017, 139(2): 021206.
Paper No: PVT-16-1023
Published Online: September 28, 2016
... internally (∼1327 °C), it results in a sudden transition of boiling crisis from nucleate to film boiling. Accordingly, from a structural integrity perspective, the RPV failure mechanisms span a wide range of structural behaviors, such as melt-through, creep damage, plastic deformation as well as thermal...
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Pressure Vessel Technol. December 2014, 136(6): 061404.
Paper No: PVT-12-1048
Published Online: September 15, 2014
...Haofeng Chen; Weihang Chen; James Ure Table 1 presents the values of equivalent creep and reverse plastic strains at the location where maximum creep strain is produced from LMM and step-by-step analysis for different material models under loading cases 2 and 3 with 10 h dwell time...
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Pressure Vessel Technol. August 2014, 136(4): 041407.
Paper No: PVT-13-1158
Published Online: April 16, 2014
... April 16, 2014. Assoc. Editor: Marina Ruggles-Wrenn. 11 09 2013 24 01 2014 Centrifugal cast 25Cr35Ni–Nb alloy furnace tubes with different contents of S are selected to investigate effects of S addition on creep and fracture behavior. Rupture tests in air at 1100 °C and 17 MPa...
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Pressure Vessel Technol. June 2014, 136(3): 031206.
Paper No: PVT-13-1023
Published Online: February 27, 2014
... ]. (See Table 2 ). Lin [ 5 ] used hypothesis for preyield creep in his model. The present model on the other hand, uses the experimental creep correlation given by Rosinger et al. [ 7 ]. The same correlations were used by Rosinger [ 15 ] for the prediction of burst strains for zircaloy-4 clads...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Pressure Vessel Technol. April 2012, 134(2): 021101.
Published Online: January 19, 2012
...Charles Becht, IV; Charles Becht, V A number of alloys have applications slightly into the creep range that are in cyclic service, such as process reactors. The 2007 edition of Section VIII, Division 2 (2007, ASME Boiler and Pressure Vessel Code, Section VIII, Division 2, The American Society...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Pressure Vessel Technol. April 2012, 134(2): 021201.
Published Online: January 11, 2012
...Basil A. Housari; Ali A. Alkelani; Sayed A. Nassar An improved mathematical model is proposed for predicting clamp load loss due gasket creep relaxation in bolted joints, taking into consideration gasket behavior, bolt stiffness, and joint stiffness. The gasket creep relaxation behavior...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Pressure Vessel Technol. February 2012, 134(1): 011211.
Published Online: December 7, 2011
... contact stress at gasket outer diameter in consideration of creeps of flanges, bolts and gasket coupled to the axial deformation compatibility equation. The analysis was verified against the finite element numerical simulation considering the nonlinear behavior of gasket and material creep. The analytical...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Pressure Vessel Technol. February 2012, 134(1): 011208.
Published Online: December 2, 2011
... to investigate the statistical variation for the anisotropic materials in strain rate effect problem and creep strain program by introducing additional six cubic slip systems into the conventional 12 octahedral slip systems inelastic range. Flow chart of mapping of boundary point to the boundary surfaces...