Graphical Abstract Figure
Abstract
MoS2-based solid lubricants have obtained significant attention and are extensively employed in the aerospace industry due to their desirable tribological performance. However, to enhance their performance in humid environments, MoS2 is often doped with Pb-based compounds. Considering the health and environmental concerns associated with Pb, it is necessary to develop eco-friendly alternatives. In this study, hexagonal boron nitride (hBN) has been used as a potential substitute for Pb-based dopants in MoS2-based solid lubricants and coatings with varying hBN contents (9.5, 11.5, 13.5, 15.5, and 17.5 wt%) were applied to stainless-steel substrates using a spray bonding technique. The friction and wear characteristics of the coatings were analyzed by using a ball-on-flat tribometer, employing constant load conditions. Subsequently, ex situ analysis techniques such as scanning electron microscopy, Raman spectroscopy, and atomic force microscopy were used to characterize the coatings. The results showed that the coating with a lower hBN concentration presented improved tribological properties, which was correlated with the development of an effective MoS2-based transfer/tribo-film. This suggests that optimizing hBN content is crucial for enhancing the lubrication performance.
References
1.
Donnet
, C.
, and Erdemir
, A.
, 2006
, “Chapter 17—Friction Mechanisms and Fundamental Aspects in Solid Lubricant Coatings,” Materials Surface Processing by Directed Energy Techniques
, Y.
Pauleau
, ed., Elsevier
, Grenoble, France
, pp. 573
–593
. 2.
Mukhtar
, S. H.
, Gulzar
, A.
, Saleem
, S.
, Wani
, M. F.
, Sehgal
, R.
, Yakovenko
, A. A.
, Goryacheva
, I. G.
, and Sharma
, M. D.
, 2024
, “Advances in Development of Solid Lubricating MoS2 Coatings for Space Applications: A Review of Modeling and Experimental Approaches
,” Tribol. Int.
, 192
, p. 109194
. 3.
Tonge
, P.
, Roy
, A.
, Patel
, P.
, Beall
, C. J.
, and Stoyanov
, P.
, 2023
, “Environmentally Friendly Bonded MoS2 Solid Film Lubricants for Aerospace Applications: Closing the Gap
,” Sustain. Mater. Technol.
, 35
, p. e00552
. 4.
Scharf
, T. W.
, and Prasad
, S. V.
, 2013
, “Solid Lubricants: A Review
,” J. Mater. Sci.
, 48
(2
), pp. 511
–531
. 5.
Gaur
, A. P. S.
, Sahoo
, S.
, Ahmadi
, M.
, Dash
, S. P.
, Guinel
, M. J.-F.
, and Katiyar
, R. S.
, 2014
, “Surface Energy Engineering for Tunable Wettability Through Controlled Synthesis of MoS2
,” Nano. Lett.
, 14
(8
), pp. 4314
–4321
. 6.
Vazirisereshk
, M. R.
, Martini
, A.
, Strubbe
, D. A.
, and Baykara
, M. Z.
, 2019
, “Solid Lubrication With MoS2: A Review
,” Lubricants
, 7
(7
), p. 57
. 7.
Jeong
, Y.
, Sung
, J. Y.
, Choi
, Y.
, Jin
, J. S.
, Yoon
, J.-H.
, Heo
, S.
, Hayakawa
, R.
, and Wakayama
, Y.
, 2019
, “Structural Characterization and Transistor Properties of Thickness-Controllable MoS2 Thin Films
,” J. Mater. Sci.
, 54
(10
), pp. 7758
–7767
. 8.
He
, T.
, Li
, Y.
, Zhou
, Z.
, Zeng
, C.
, Qiao
, L.
, Lan
, C.
, Yin
, Y.
, Li
, C.
, and Liu
, Y.
, 2019
, “Synthesis of Large-Area Uniform MoS2 Films by Substrate-Moving Atmospheric Pressure Chemical Vapor Deposition: From Monolayer to Multilayer
,” 2D Mater.
, 6
(2
), p. 025030
. 9.
Tonge
, P.
, Roy
, A.
, Patel
, P.
, Beall
, C. J.
, and Stoyanov
, P.
, 2022
, “Tribological Evaluation of Lead-Free MoS2-Based Solid Film Lubricants as Environmentally Friendly Replacements for Aerospace Applications
,” Lubricants
, 10
(1
), p. 7
. 10.
Sun
, S.
, Chen
, J.
, Wang
, Y.
, Wang
, L.
, and Sun
, Z.
, 2020
, “Structural Sensitivity of MoS2-Based Films in Solid Space Lubrication
,” Surf. Eng.
, 36
(1
), pp. 106
–113
. 11.
Wang
, Q. J.
, and Chung
, Y.-W.
, 2013
, Encyclopedia of Tribology
, Springer
, New York
.12.
Lince
, J. R.
, 2020
, “Effective Application of Solid Lubricants in Spacecraft Mechanisms
,” Lubricants
, 8
(7
), p. 74
. 13.
Kim
, J.
, Lee
, Y.
, and Yang
, M.
, 2014
, “Environmental Exposure to Lead (Pb) and Variations in Its Susceptibility
,” J. Environ. Sci. Health Part C
, 32
(2
), pp. 159
–185
. 14.
Senatore
, A.
, Risitano
, G.
, Scappaticci
, L.
, and D’Andrea
, D.
, 2021
, “Investigation of the Tribological Properties of Different Textured Lead Bronze Coatings Under Severe Load Conditions
,” Lubricants
, 9
(4
), p. 34
. 15.
Oksanen
, V. T.
, Lehtovaara
, A. J.
, and Kallio
, M. H.
, 2017
, “Load Capacity of Lubricated Bismuth Bronze Bimetal Bearing Under Elliptical Sliding Motion
,” Wear
, 388–389
, pp. 72
–80
. 16.
Scharf
, T. W.
, Kotula
, P. G.
, and Prasad
, S. V.
, 2010
, “Friction and Wear Mechanisms in MoS2/Sb2O3/Au Nanocomposite Coatings
,” Acta Mater.
, 58
(12
), pp. 4100
–4109
. 17.
Lu
, X.-L.
, Liu
, X.-B.
, Yu
, P.-C.
, Qiao
, S.-J.
, Zhai
, Y. J.
, Wang
, M. D.
, Chen
, Y.
, and Xu
, D.
, 2016
, “Synthesis and Characterization of Ni60-hBN High Temperature Self-Lubricating Anti-Wear Composite Coatings on Ti6Al4V Alloy by Laser Cladding
,” Opt. Laser Technol.
, 78
, pp. 87
–94
. 18.
Kumar
, R.
, Aydinyan
, S.
, Ivanov
, R.
, Liu
, L.
, Antonov
, M.
, and Hussainova
, I.
, 2022
, “High-Temperature Wear Performance of hBN-Added Ni-W Composites Produced From Combustion-Synthesized Powders
,” Materials
, 15
(3
), p. 1252
. 19.
Torres
, H.
, Podgornik
, B.
, Jovičević-Klug
, M.
, and Rodríguez Ripoll
, M.
, 2022
, “Compatibility of Graphite, hBN, and Graphene With Self-Lubricating Coatings and Tool Steel for High Temperature Aluminium Forming
,” Wear
, 490–491
, p. 204187
. 20.
Joseph
, A.
, Gautham
, V.
, Akshay
, K. S.
, and Sajith
, V.
, 2022
, “2D MoS2-hBN Hybrid Coatings for Enhanced Corrosion Resistance of Solid Lubricant Coatings
,” Surf. Coat. Technol.
, 443
, p. 128612
. 21.
Joseph
, A.
, Akshay
, K. S.
, and Sajith
, V.
, 2023
, “Synergistic Effect of Ceria-Zirconia Nanoparticles and hBN Nanosheets Incorporation on the Corrosion Resistance of MoS2 Solid Lubricant Coatings
,” Surf. Coat. Technol.
, 473
, p. 130025
. 22.
Kumar
, R.
, and Antonov
, M.
, 2021
, “Self-Lubricating Materials for Extreme Temperature Tribo-Applications
,” Mater. Today: Proc.
, 44
, pp. 4583
–4589
. 23.
Podgornik
, B.
, Kosec
, T.
, Kocijan
, A.
, and Donik
, Č
, 2015
, “Tribological Behaviour and Lubrication Performance of Hexagonal Boron Nitride (h-BN) as a Replacement for Graphite in Aluminium Forming
,” Tribol. Int.
, 81
, pp. 267
–275
. 24.
Kimura
, Y.
, Wakabayashi
, T.
, Okada
, K.
, Wada
, T.
, and Nishikawa
, H.
, 1999
, “Boron Nitride as a Lubricant Additive
,” Wear
, 232
(2
), pp. 199
–206
. 25.
Kumar
, R.
, Hussainova
, I.
, Rahmani
, R.
, and Antonov
, M.
, 2022
, “Solid Lubrication at High Temperatures—A Review
,” Materials
, 15
(5
), p. 1695
. 26.
Everlube Products
, 2024
, “Everlube® 620C: Mil Spec MoS2 Solid Film Lubricant
,” Technical Data Sheet, Everlube Products, Surface Technologies Division, Peachtree City, GA. https://everlubeproducts.com/prod/docs/tds/Everlube620CTDS.pdf.27.
Everlube Products
, 2023
, “Process Bulletin 3000-A—Solid Film Lubricants & Engineered Coatings: Recommended Application Procedure
,” Everlube Products, Surface Technologies Division, Peachtree City, GA. https://everlubeproducts.com/prod/docs/processbulletins/3000APB.pdf.28.
Luo
, Q.
, 2013
, “Tribofilms in Solid Lubricants,” Encyclopedia of Tribology
, Q. J.
Wang
, and Y. W.
Chung
, eds., Springer
, Boston, MA
, pp. 3760
–3767
.29.
Manu
, B. R.
, Gupta
, A.
, and Jayatissa
, A. H.
, 2021
, “Tribological Properties of 2D Materials and Composites—A Review of Recent Advances
,” Materials
, 14
(7
), p. 1630
. 30.
Hutchings
, I.
, and Shipway
, P.
, 2017
, Tribology: Friction and Wear of Engineering Materials
, Butterworth-Heinemann
, UK
.31.
Aranganathan
, N.
, Bijwe
, J.
, and Khatri
, D.
, 2016
, “Role of Combination of Hexagonal Boron Nitride and Graphite in NAO Friction Material
,” Proc. Inst. Mech. Eng., Part J: J. Eng. Tribol.
, 230
(9
), pp. 1107
–1112
. 32.
Honglin
, M.
, Haichao
, Z.
, Honggang
, T.
, Guozheng
, M.
, Ming
, L.
, Haidou
, W.
, Fengkuan
, X.
, and Zhihai
, C.
, 2024
, “Effects of hBN Content and Particle Size on Microstructure, Mechanical and Tribological Properties of NiCr-Cr3C2-hBN Coatings
,” Surf. Coat. Technol.
, 478
, p. 130330
. 33.
Stoyanov
, P.
, Chromik
, R. R.
, Goldbaum
, D.
, Lince
, J. R.
, and Zhang
, X.
, 2010
, “Microtribological Performance of Au–MoS2 and Ti–MoS2 Coatings With Varying Contact Pressure
,” Tribol. Lett.
, 40
(1
), pp. 199
–211
. 34.
Chen
, J. M.
, and Wang
, C. S.
, 1974
, “Second Order Raman Spectrum of MoS2
,” Solid State Commun.
, 14
(9
), pp. 857
–860
. 35.
Singh
, H.
, Mutyala
, K. C.
, Evans
, R. D.
, and Doll
, G. L.
, 2015
, “An Investigation of Material and Tribological Properties of Sb2O3/Au-Doped MoS2 Solid Lubricant Films Under Sliding and Rolling Contact in Different Environments
,” Surf. Coat. Technol.
, 284
, pp. 281
–289
. 36.
Jones
, R.
, Pollock
, H. M.
, Cleaver
, J. A. S.
, and Hodges
, C. S.
, 2002
, “Adhesion Forces Between Glass and Silicon Surfaces in Air Studied by AFM: Effects of Relative Humidity, Particle Size, Roughness, and Surface Treatment
,” Langmuir
, 18
(21
), pp. 8045
–8055
. 37.
Jiang
, T.
, and Zhu
, Y.
, 2015
, “Measuring Graphene Adhesion Using Atomic Force Microscopy With a Microsphere Tip
,” Nanoscale
, 7
(24
), pp. 10760
–10766
. 38.
Fayeulle
, S.
, Ehni
, P. D.
, and Singer
, I. L.
, 1990
, “Role of Transfer Films in Wear of MoS2 Coatings
,” Tribol. Ser.
, 17
, pp. 129
–138
. 39.
Wahl
, K. J.
, and Singer
, I. L.
, 1996
, “Role of the Third Body in Life Enhancement of MoS2
,” Tribol. Ser.
, 31
, pp. 407
–413
. 40.
Godet
, M.
, 1984
, “The Third-Body Approach: A Mechanical View of Wear
,” Wear
, 100
(1–3
), pp. 437
–452
. 
